 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MC-ACT-VME2416 February 25, 2003 VME2416 Datasheet v1.3 MemecCore Product Line 3721 Valley Centre Drive San Diego, CA 92130 USA Americas: +1 800-752-3040 Europe: +41 (0) 32 374 32 00 Asia: +(852) 2410 2720 E-mail: actel.info@memecdesign.com URL: www.memecdesign.com/actel TM Product Summary Intended Use * * * * * * * * * * * * * Medical systems Industrial controls: robotic, factory automation Key Features Flexible slave VME controller Full interrupt controller (ROAK) Control signals for external drivers and drivers on chip Synchronous user side interface for registers, peripherals and memories User definable waitstates Synchronous, reliable design Expandible to full set of VME features Silicon proven design Targeted Devices SX-A Family Axcelerator Family ProASIC PLUS Family General Description The MC-ACT-VME2416 core is used as interface for the VME standard bus. One side contains all VME bus signals and the other side all the user signals. With the defined address and address modifier, the user allows any masters on the VME bus to access the IO, peripherals or memory placed on the user side. The user has to describe two blocks which are connected to the "address decoding" and to the "user side". The "address decoding" is used to detect the access and to allow the transfer on the corresponding board. It allows the user to built its own address decoding without changing the code of the MC-ACT-VME2416. The MC-ACT-VME2416 core provides a full interrupt controller based on seven interrupt lines connected to the bus. The system release the interrupt on the acknowledge (ROAK). The acknowledge is done on all boards connected on the bus through a daisy-chain. A complete VHDL test bench verifies every functions and addressing mode and interrupts. These testbenches are built as a self testing regression-test suite. February 25, 2003 1 Optimized for VME2416 Core Deliverables * * Netlist Version o Netlist compatible with the Actel Designer place and route tool RTL Version o VHDL Source Code o Test Bench All o User Guide Memec Design * Synthesis and Simulation Support * * * * Synthesis: Synplicity Simulation: ModelSim Other tools supported upon request Verification Test Bench MC-ACT-VME2416 VME_ADDR[23:1] VME_AM[5:0] VME_DATA_IN[15:0] VME_DATA_OUT[15:0] VME_EXT_DRV_N VME_EXT_DDIR VME_INT_DRV_N VME_DTACK_N VME_AS_N VME_DS0_N VME_DS1_N VME_LWORD_N VME_WRITE_N VME_BERR_N VME_IACK_N VME_IACKOUT_N VME_IACKIN_N VME_IRQ_N[6 :0] CLK RESET_N USER_ADDR[23 :1] USER_AM[5 :0] USER_RW_N USER_WR_DATA[15 :0] USER_BE1 USER_BE2 USER_RD_DATA[15 :0] USER_ACC_REQ USER_ACC_RDY USER_IREQ USER_ILEV[2 :0] USER_IVEC[15 :0] USER_IACK VMEbus signals Address decoding Interrupt port User side signals Figure 1: MC-ACT-VME2416 Pinout February 25, 2003 User Address Decode INT_USER_AM[5 :0] INT_USER_ADDR[15 :1] USER_ACC System Optimized for 2 VME2416 Functional Description Memec Design The falling edge of VME_AS (address strobe) will synchronize all the addresses (VME_ADDR and VME_AM) allowing the controller to decode them in order to define if the present board is addressed or not. Since this moment, all signals on the VME bus have to be stable and the controller will execute the command depending on the control signals (VME_DS0_N, VME_DS1_N, VME_WRITE_N, VME_IACK_N). The VME master has to release the VME_AS_N signal at the end of a transfer to execute a new command. WRITE DATA TRANSFER When the VME_WRITE_N defines a write data transfer, the controller will assign the address (VME_ADDR) on the USER_ADDR bus, the address modifier (VME_AM) on the USER_AM bus and the data (VME_DATA) on the USER_DATA bus. The signals VME_DS0_N and VME_DS1_N select the corresponding data location according the following table (for this model of VME controller-MC-ACT-VME2416-, the signals VME_LWORD and VME_ADDR01 are don't care): Data Locations Selected VME_DS0_N VME_DS1_N VME_ADDR01 VME_LWORD_N VME_DATA_IN(7:0) low high X X VME_DATA_IN(15:8) high low X X VME_DATA_IN(15:0) low low X X To execute the transfer on the user part, the controller will active a request signal (USER_ACC_REQ) with valid control signals. The data locations selected are enabled with the signals USER_BE1 (bits 7:0) and USER_BE2 (bits 15:8). The transfer will be ended with the acknowledge of the user part (USER_ACC_ACK). Once the transfer executed, the controller will acknowledge the data transfer on the VME bus with the VME_DTACK_N. When seeing this acknowledge, the master will release the VME_AS_N signal ending the actual data transfer. READ DATA TRANSFER When the VME_WRITE_N defines a read data transfer, the controller will assign the address (VME_ADDR) on the USER_ADDR bus and the address modifier (VME_AM) on the USER_AM bus. As the write data transfer, the signals USER_BE1/2 are depending on the VME_DS0/1_N. The controller will active a request signal (USER_ACC_REQ) until the acknowledge (USER_ACC_ACK) coming from the user part. The read data have to be valid during this acknowledge. Once ready, the data are transferred on the VME_DATA_OUT bus and acknowledged with the signal VME_DTACK_N. When seeing this acknowledge, the master will release the VME_AS_N signal ending the actual data transfer. INTERRUPT The interrupts on the VME bus are generated by the different modules connected on the bus and are acknowledged through a daisy-chain interrupt line as shown on the figure below: Memory Board (user part) Interrupt Handler IO Board (user part) MC-ACTVME VME Interface MC-ACTVME iackin_n iackout_ n iackout_ n iackin_n iackin_n iack_n iack_n February 25, 2003 iack_n iackout_ n iack_n Optimized for 3 VME2416 Memec Design Between the user part and the VME controller, the transfer of interrupt information is based on the request/acknowledge protocol. When an interrupt occurs on the user part, it generates an interrupt request on the VME controller through the signal USER_IREQ. Depending on the value defined by the user part on the vector USER_ILEV, the VME controller activates an interrupt on the respective interrupt line VME_IRQ_N(x) (USER_ILEV = 1 -> VME_IRQ_N(1), USER_ILEV = 7 -> VME_IRQ_N(7)). Interrupt level 7 has the highest priority and interrupt level 1 has the lowest. Since there, the interrupt handler acknowledges the interrupt by asserting a low state on the signal VME_IACK_N. This signal will be transmitted to all modules and as well in the first module of the daisy-chain. The modules which didn't generate an interrupt just assert the VME_IACKIN_N signal to the VME_IACKOUT_N. A module which generated an interrupt will detect the acknowledge at the falling edge and compare the VME_ADDR(3:1) with the interrupt level register (USER_ILEV) to determine if it has the priority (depending on the level) to execute the interrupt or not. In case of not, it will assign the VME_IACKIN_N to VME_IACKOUT_N. In the other case (the corresponding module has the priority), the high state is asserted to the VME_IACKOUT_N signal in order to break the daisy-chain and avoid other modules taking the interrupt acknowledge. During the acknowledge, the module transfers the interrupt vector register defined by the user (USER_IVEC) on the VME data bus (VME_DATA_OUT). When the data are valid, the VME controller drives the VME_DTACK_N signal low, allowing the master and interrupt handler executing next commands. On the user part, the interrupt is acknowledged with the signal USER_IACK which clears the pending interrupt request. Device Requirements Family SX-A PLUS ProASIC Axcelerator Device SX32A-STD APA150-STD AX500-STD COMB 66 (4%) n/a 65 (2%) Utilization SEQ 135 (13%) n/a 135 (5%) Performance Total 201 (7%) 295 (5%) 200 (3%) 138 MHz 112 MHz 159 MHz Table 1: Device Utilization and Performance Verification and Compliance Complete functional and timing simulation has been performed on the VME using ModelSim 5.5e. This core has also been used successfully in customer designs. February 25, 2003 Optimized for 4 VME2416 Signal Descriptions The following signal descriptions define the IO signals. Signal Direction Description CLK RESET_N VME_ADDR[23:1] VME_AM[5:0] VME_DATA_IN[15:0] VME_DATA_OUT[15:0] VME_EXT_DRV_N VME_INT_DRV_N VME_EXT_DDIR VME_LWORD_N VME_DTACK_N VME_AS_N Input Input Input Input Input Output Output Output Output Input Output Input Memec Design VME_DS0_N VME_DS1_N VME_WRITE_N VME_BERR_N VME_IACK_N Input Input Input Input Input VME_IACKIN_N VME_IACKOUT_N VME_IRQ_N[6:0] Input Output Output INT_USER_ADDR[23:1] Output INT_USER_AM[5:0] Output USER_ACCESS Input Clock: System clock. This clock is provided by the user side interface which is part of the 40MHz clock domain. System reset: Asynchronous system reset, active low. VME Address Bus: The smallest addressable unit is the byte location. Masters use address lines to select the data which has to be accessed VME Address Modifier Bus: Allow the master to pass additional binary information to the slave during data transfer cycles. VME Data Bus In: 16 write data lines are available. Depending on the control signals, only one byte can be used for the transfer on the user part. VME Data Bus Out: 16 read data lines. For each access, the 16 data bits are read. VME External Data Drive: Active low drive enable signal for external bidirectional data bus drivers. VME Internal Data Drive: Active low drive enable signal for internal bidirectional data bus drivers. VME External Data Direction: Direction control signal for internal bidirectional data bus drivers. High indicates data to VME bus and low from VME bus. VME Long Word: Active low signal indicating long word access. This signal is not used in the MC-ACT-VME2416. VME Data Acknowledge: This active low signal acknowledges the data transfer. It has to be connected to an open collector driver. VME Address Strobe: clocks with falling edge the internal synchronization signals like VME_ADDR and VME_AM. It is also used as data signal for access start detection. VME Data Strobe 0: Active low signal used for the selected location part of the data. Data strobe 0 is dedicated to the data[7:0]. VME Data Strobe 1: Active low signal used for the selected location part of the data. Data strobe 1 is dedicated to the data[15:8]. VME Read/Write: Active low signal which is used by the master to indicate the data direction. VME Bus Error: Active low signal driven by other modules indicating that the data transfer was unsuccessful. VME Interrupt Acknowledge: When driven low, the VME_IACKIN_N causes the IACK daisy-chain driver, located in slot 1, to propagate a falling edge down the interrupt acknowledge daisy-chain. VME Interrupt Acknowledge Input Daisy-Chain: This active low signal is used as input of the module for the daisy-chain interrupt acknowledge. VME Interrupt Acknowledge Output Daisy-Chain: This active low signal is used as output of the module for the daisy-chain interrupt acknowledge. VME Interrupt Request Lines: Interrupters request interrupts by driving an interrupt request line low. VME_IRQ_N[7] has the highest priority. These signals have to be connected to open collector drivers. Registered VME Address Bus: Synchronized on the falling edge of VME_AS_N. This bus is used to decode the address and to active an access signal on the user part. Registered VME Address Modifier Bus: Synchronized on the falling edge of VME_AS_N. This bus is used to decode the address modifier and to active an access signal on the user part. User Access Signal: The user has 50 ns time to decode the address and asserting the USER_ACCESS signal when addressed. February 25, 2003 Optimized for 5 VME2416 Signal USER_ACC_REQ Memec Design Direction Output Description User Access Request: Active high signal which requests for an access on the VME bus. Valid until USER_ACC_RDY acknowledges the request (or VME bus error occurs). User Side Acknowledgement Signal: Acknowledge the request of the access on the VME bus of the user part. User Address: Address used for the access on the user part. User Address Modifier: Address modifier used for the access on the user part. User Write Data: The MSB data [15:8] are valid while USER_BE2 is high and LSB data [7:0] while USER_BE1 is high. User Read Data: The read data has to be valid when USER_ACC_RDY is high. User Read/Write Signal: A low signal indicates that the data are written in the user part and a low signal, that the data are read. User Byte 1 Enable: Active high signal enabling the low byte [7:0] of the data. User Byte 2 Enable: Active high signal enabling the high byte [15:8] of the data. User Interrupt request: This active high signal indicates that an interrupt is pending on a VME interrupt will be generated. It will return to zero with USER_IACK active. User Interrupt Acknowledge: An active one event which indicates the end of a valid interrupt acknowledge cycle. User Interrupt Level: This bus indicates the level of priority of the pending interrupt. It will generate the corresponding VME_IRQ. User Interrupt Vector: The interrupt vector will be transmitted on the VME data bus during the acknowledgement of the interrupt. USER_ACC_RDY USER_ADDR[23:1] USER_AM[5:0] USER_WR_DATA[15:0] USER_RD_DATA[15:0] USER_RW_N USER_BE1 USER_BE2 USER_IREQ Input Output Output Output Input Output Output Output Input USER_IACK USER_ILEV[2:0] USER_IVEC[15:0] Output Input Input Table 2: VME Core Signal List February 25, 2003 Optimized for 6 VME2416 Recommended Design Experience Memec Design For the source version, users should be familiar with HDL entry and Actel design flows. Users should be familiar with Actel Libero v2.2 Integrated Design Environment (IDE) and preferably with Synplify and ModelSim. Ordering Information Part Number MC-ACT-VME2416-NET MC-ACT-VME2416-VHD Description Core Netlist Core VHDL Table 3: Core Part Numbers The CORE is provided under license from Memec Design for use in Actel programmable logic devices. Please contact Memec Design for pricing and more information. Information furnished by Memec Design is believed to be accurate and reliable. Memec Design reserves the right to change specifications detailed in this data sheet at any time without notice, in order to improve reliability, function or design, and assumes no responsibility for any errors within this document. Memec Design does not make any commitment to update this information. Memec Design assumes no obligation to correct any errors contained herein or to advise any user of this text of any correction, if such be made, nor does the Company assume responsibility for the functioning of undescribed features or parameters. Memec Design will not assume any liability for the accuracy or correctness of any support or assistance provided to a user. Memec Design does not represent that products described herein are free from patent infringement or from any other third-party right. No license is granted by implication or otherwise under any patent or patent rights of Memec Design. MemecCore products are not intended for use in life support appliances, devices, or systems. Use of a MemecCore product in such application without the written consent of the appropriate Memec Design officer is prohibited. All trademarks, registered trademarks, or service marks are property of their respective owners. Datasheet Revision History Version Datasheet 1.0 Datasheet 1.1 Datasheet 1.2 Datasheet 1.3 Date January 8, 2003 January 23, 2003 January 29, 2003 February 25, 2003 Description Initial Release Modification done in section core deliverables; Added logo to footer Modification done in section device requirements Modification done in section device requirements, new URL and address inserted February 25, 2003 Optimized for 7 |
Price & Availability of MC-ACT-VME2416
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |